Clean Air Services, Inc.'s air duct cleaning process can reduce moisture, dirt, pollen, fungus, bacteria and other debris in your HVAC system. Most homes have been using inefficient, throwaway filters rather than HEPA 99% efficient filters. Throwaway filters are only 7%-10% efficient. Clean Air Services, Inc. systems utilize a push/pull cleaning technique, the most effective source removal method currently available. The push/pull concept uses compressed air and physical agitation to break debris free and push it through the ductwork while a powerful vacuum downstream pulls loosened material through and out of the HVAC system. The supply and return sides of the HVAC system are "zoned" so they can be cleaned separately. This is usually accomplished using zone bags, foam blocks or by simply removing the filter from the HVAC system, placing it in a plastic bag and reinstalling it. An access hole is cut into the supply side of the HVAC system, the vacuum is connected using a connection collar and the vacuum is turned on.

Starting with the farthest branch from the vacuum and working toward the closest, each branch is individually cleaned back to the main trunk using a combination of compressed air and physical agitation after each register is removed and contact cleaned. After all the branch runs have been cleaned, the main trunk is cleaned back to the vacuum. Once the supply side has been cleaned, an access hole is cut into the return side, the vacuum is attached and the cleaning process is repeated. In addition to cleaning the interior of the duct, a complete cleaning would include: cleaning the fan, coil and registers and inspection or replacement system's air filter. Upon completion of the cleaning process, an EPA-approved sanitizer treatment is applied over all interior surfaces of the HVAC system, to include air handlers, supply, return, exhaust and intake ducts and mixing boxes. As the vacuum unit is running, the negative pressure "pulls" the sanitizer throughout the ductwork.

After all cleaning and sanitizing operations are completed; an EPA registered anti-microbial encapsulate is applied at each supply duct end to help prevent contamination caused by excess moisture/condensation due to the varying temperature differences at these areas. The encapsulate is also applied to the fibrous material (ex. insulation) of the return and unit. Clean Air Services, Inc.'s proven cleaning technique is performed by experienced professionals following current industry guidelines in residential and commercial environments. air purifiers that eliminate cigarette smokeOur professionals comprise an environmental management team, which includes a Certified Indoor Environmentalist and Certified Mold Remediator, who can offer solutions to all of your indoor air quality concerns.counter top air purifiers

Your text message was sent. To opt out at anytime, send the word STOP to YP411 from your mobile phone. To get a help message, send the word HELP to YP411 from your mobile phone. Send this business listing as a text message to a mobile phone. Clean Air Services, Inc. 601-583-6690, 228-436-4272, 601-978-6833, 601-693-0371, 251-660-6090, 504-831-7323, 985-690-6066, 1-866-444-4AIR Terms: The recipient of this text message may incur charges depending on their wireless carrier. best air purifier for sleepingNot all carriers are currently supported Cutting a hole to fit a roof air vent does not have to be a very complicated process. If you have any doubts about cutting a hole in your roof you can always have experienced roofers fit the vent for you, but most people with a small amount of home improvement knowledge can complete it to a suitable standard. Whether you are a hardened home improvement fan, or a beginner in DIY, fitting a vent can be done in a day if you follow a few simple guidelines.

Step 1 - Cutting a Hole Before you begin cutting your hole, you will need to mark out the area where you intend your vent to go. If you are fitting a gable end vent, for example, this is much simpler than fitting a large air vent into the middle of your roof. Putting your vent into the middle of the roof requires that you remove any tiles or slate that may be damaged when you make the hole. Keep these pieces safe for use later. Once the roof has its shingles removed you can begin cutting. Remove any drywall from the inside, and then cut through to the outside of the roof. Be careful not to damage any foundation beams, supports, or other essential columns. Step 2 - Fitting the Air Vent Place the air vent into the hole and then screw it tightly into position. The hole should be just large enough to accommodate the vent, but not much bigger. When the air vent is screwed into place, you can place caulk around the edge of the frame and then seal over the inside with tape, such as duct tape.

This should be pressed hard into the wall, so that the tape and caulk are secure. This will help prevent the vent from collapsing. Once this is complete, connect any fans or other motors to your vent, and operate them in order to make sure that the vent is fitted securely and the caulk and tape is not affecting the turning of fans. Step 3 - Filling the Hole Now that you have fitted the vent, you should go around to the outside of the roof again and replace the tiles and shingles that you removed earlier. Some pieces will need to be cut in half, or left out altogether, in order to ensure that there is no obstruction of the vent. Once these tiles or slates have been replaced, you should add caulking all around the outside, and then pour a layer of waterproofing roof tar over the surface. This will help to ensure that any cracks left accidentally during the replacing will be watertight. The caulking and tar should be left to dry thoroughly before any fans or motors in the vent are operated again, but the vent should now be safely installed in your roof.